Electronic Test Equipment

Clamp Meters

Fluke 376 Clamp Meter


The Fluke 376 Clamp Meter offers improved performance perfect for a wide range of current measurement situations. With true-rms voltage and current measurements, the Fluke 376 can read up to 1000 V and 1000 A in both ac and dc modes.

Features and benefits

  • CAT IV 600 V, CAT III 1000 V
  • True-rms ac voltage and current for accurate measurements on non-linear signals
  • Min, max, average and inrush recording to capture variations automatically
  • Integrated low pass filter and state of the art signal processing allows for use in noisy electrical environments while providing stable readings
  • Proprietary inrush measurement technology to filter out noise and capture motor starting current exactly as the circuit protection sees it
  • Ergonomic design fits in your hand and can be used while wearing protective equipment
  • Large, easy to read backlight display automatically sets the correct measurement range so you do not need to change the switch positions while taking a measurement

Pro Sys CP41 Current Clamp Meter


The CP 41 current clamp meter has been designed for reliable and accurate, non-intrusive measurement of AC, DC and complex waveform currents. Using advanced Hall Effect technology the CP 41 can measure currents accurately from 5mA to 40Amps.

Measurement features include:

  • True RMS reading
  • 1mA/ 10mA Resolution
  • Auto ranging/Auto Power Off
  • Data Hold

Typical Applications

  • Leakage current measurements (CP41)
  • Process control for 4 – 20mA current loop verification (CP41)
  • Battery charging systems
  • Starting currents
  • Light industrial and residential electrical installation testing

LCR Meters

Amprobe LCR55A Capacitance Tester


The ultimate electronic component verifier measures inductance, capacitance, resistance, transistors, diodes and microwave diodes.

  • The ultimate component checker measures inductance, capacitance, resistance, transistors, diodes and microwave diodes
  • Plug-in test slots and test leads with threaded alligator clips
  • Oversized, digital display
  • Data Hold and Max Hold
  • "Zero Adjust" Pot for Ohms
  • Low Battery Indication
  • Auto-Power Off

REED R5001


  • Measure inductance/capacitance/resistance with secondary parameters including dissipation
factor (D), quality factor (Q), phase angle (Ø), equivalent series/parallel resistance (ESR or Rp)
  • Auto ranging operation for AC impedance and DE resistance measurement
  • Auto LCR smart check and measurement
  • Series/Parallel modes
  • Ls/Lp/Cp with D/Q/Ø/ESR parameters
  • Support DCR mode 200 to 200MΩ
  • High accuracy with 4 or 5 terminal Kelvin measurement
  • Testing frequency is up to 10kHz and output frequency is up to 100kHz
  • Dual display with backlight
  • Data hold function
  • Low battery indication with auto power off
  • Dust and water proof to IP67

Multifunction Testers

Fluke 789 Process Meter


The Fluke 787 was the first tool to combine a DMM and a loop calibrator to give process technicians double the power in one tool. Now it’s even better, the range is extended with the Fluke 789 – the ultimate loop calibration multimeter. The Fluke 789 has a 24-Volt loop supply reducing the need for taking a separate power supply when doing offline transmitter testing. And with its built-in, selectable 250-Ohm Hart® resistor, it also eliminates the need to carry a separate resistor with you.

Features of the Fluke 789

  • 24 V Loop power supply
  • Very large dual display
  • Enhanced backlight with 2 brightness settings
  • 1200 ohm drive capability on mA source
  • HART mode setting with loop power and a built-in 250 ohm resistor
  • 0% and 100 % buttons to toggle between 4 and 20 mA sourcing for a quick span check
  • Externally accessible fuses for easy replacement
  • Infrared-port to process data in FlukeView Forms (V2.1) software

Fluke 1653B Multifunction Tester


The 1653B Installation Tester verifies the safety of electrical installations in domestic, commercial and industrial applications. It can ensure that fixed wiring is safe and correctly installed to meet the requirements of IEC 60364, HD 384 and all relevant local standards.

Faster

  • Two measurements at once and a dual display. PEFC/PSC and loop impedance are measured and displayed in parallel, saves you more than 50% of test time compared to other loop testers.
  • Additional new high current loop mode. Faster measurements compared to loop tests with non-trip mode for RCD’s.
  • Unique zero adapter for fast, always reliable and accurate test lead and mains cord compensation.
  • Fast voltage measurement between L-N, L-PE and N-PE using the mains cord. No need to change measurement connections.

Safer

  • Earth Volt Touchpad detects raised earth voltages >50 V, indicating potential dangerous situations.
  • Supplied with the Sure Grip™ test leads and clips which gives the user a comfortable, reliable grip

Easy

  • Rotary dial knob indicates clearly which function is selected, all functionalities on one spot and no complex multi-level menus.
  • Large display with backlight, clear symbols and exceptionally wide viewing angle for easy and safe readings.
  • PASS/FAIL indication for RCD test results.
  • Variable RCD current mode for customized settings.

Multimeter

Fluke 179 True-rms Digital Multimeter with Temperature


True-rms digital multimeter designed with a built-in thermometer. Two tools in one.

The new Fluke 179 has features and functions needed to troubleshoot your equipment and plant.

  • True-rms ac voltage and current for accurate measurements on non-linear loads
  • Large digit display with analogue bar graph
  • Display backlight for work in dark areas
  • Temperature and capacitance
  • Records minimum and maximum values to aid in troubleshooting

Latest Group News

Group News